Popcorn Ceiling Removal in Conroe, TX | Conroe Drywall Co.

Conroe Drywall Co. has provided popcorn ceiling removal for homeowners and property managers in Conroe, Texas for over 15 years. The bumpy white coating overhead is usually older than the room around it, staying in place through new paint, new floors and new light fixtures. Popcorn ceilings come in several forms, and each one reacts differently once a knife touches it. Sprayed acoustic texture was blown on wet through a hose and dries into loose popcorn-shaped lumps, while hand-applied texture was troweled on and bonds much more tightly. Any acoustic ceiling texture that has been painted since resists water, and a ceiling put up before 1990 goes to a laboratory for testing before anything is disturbed.

Scraping is the short part of the job. We wet the surface with a pump sprayer, remove the softened texture with a broad knife, and seal off the room so the mess stays contained. The longer part is rebuilding the surface: two or three skim passes of joint compound to build a smooth ceiling, sanding, a sealing coat of ceiling primer, and a finish that is either a flat plane or a light texture. GA-214, the Gypsum Association's grading system for how far board is finished, provides the language used to describe a flat ceiling.

Repairing an existing texture without removing it is ceiling repair, a new ceiling is ceiling installation, and finish painting is a separate service. We work throughout Willis, Montgomery, the Lake Conroe communities and Montgomery County, and we settle what goes back on your ceiling before anything comes off. Call (346) 488-0243 for a free on-site estimate and a written price.

Get A Free Estimate

Scraping Is the Short Part of Popcorn Ceiling Removal

Only one part of this job involves a scraper. We first identify the texture, test it when its age requires it, and protect the room before scraping the texture away. Once the ceiling is exposed, we repair any damage underneath, skim the surface flat with joint compound, sand it smooth, and apply primer. A skim coat is a thin layer of joint compound spread across the entire ceiling to fill the shallow dips and knife marks left behind, and that finishing work accounts for most of the hours.

Scraping a single room takes about one working day, but bringing that same room to a smooth ceiling finish takes several visits because joint compound has to dry between coats, and sanding cannot begin until the final coat is dry.

A quote that covers only the scraping therefore prices the smaller part of the work. The condition of the ceiling decides how much finishing follows: texture that releases cleanly leaves less repair behind, while texture that resists water takes more time to remove and smooth.

The Three Textures That Come Off Differently

Three different ceiling finishes get called popcorn, and each one behaves differently under a scraper. True sprayed acoustic texture was blown onto the board wet, so it sits proud of the surface and crumbles when it is wetted again. Hand-applied texture was worked on with a tool instead of sprayed, and although it can look almost identical from the floor, it comes off differently and at a different pace. A painted popcorn ceiling is the third and most difficult case because the paint film sheds water instead of letting it soak in.

You can tell a great deal from the floor without going near a ladder. Acoustic ceiling texture has sharp, irregular peaks with no shine, while a painted surface has softer tips and picks up a faint sheen where light crosses it. What settles the question is a coin-sized scratch in a closet corner where no one looks. That small test patch shows how the material sits on the board and how readily it releases, which a photograph cannot. Which of the three is overhead determines both the removal method and the number of labor hours.

From Scrape to Paint-Ready, and Where We Stop

Our work on your ceiling ends with a flat, sanded and primed surface. Ceiling primer is the sealing coat rolled over the bare board and dried joint compound so the finish paint sits evenly across both, and we include it because a paint-ready ceiling is not ready without it. The finish coat itself is a separate service, quoted on its own, so it is not included in this price and there is no confusion about where our ceiling work ends.

Two related jobs are quoted separately from popcorn ceiling removal: repairing an existing texture while leaving it in place, and hanging a new ceiling. We cover and protect your walls and trim throughout the work, but restoring them to finished condition is outside this scope as well. Each item appears as its own line on the written scope, so you know exactly what the price includes and what it does not before you agree to the work.

One Room, One Level, or the Whole House

A single room ceiling is a complete job on its own, and we do not require a minimum that pushes you into more work than you want. Connected rooms are usually better handled together because an open-plan living and dining area shares one continuous ceiling plane that your eye follows from end to end. Where a finished ceiling meets one that still has texture, the transition remains visible from anywhere in the room, and careful work at the junction does not make that line disappear.

Whole-house popcorn removal in a single-story home with around 1,800 square feet of ceiling is handled as a multi-day sequence, working room by room so you can keep part of the house in use throughout. Plastic sheeting goes up and comes down once per work area rather than once per ceiling, which lowers the protection cost per room as the project moves through more of the house.

A brown water stain spreading across a popcorn ceiling around a sagging patch
Popcorn texture removed with a vacuum sander in a plastic-masked room

Should You Remove the Popcorn or Cover It?

Removing sprayed acoustic texture is a choice rather than work the building requires, and scraping is not always the right way to get rid of the visible texture. Texture sealed under paint resists the water used to soften it and can turn scraping into hours of dry chipping. A ceiling already covered with old patchwork may still need extensive flattening after the texture comes off. In those two cases, leaving the old surface in place and covering it can avoid paying for removal before doing much of the same finish work.

When Covering the Existing Texture Makes Sense

We start by checking that your ceiling is sound and dry. Covering begins with a bonding primer, a liquid coat that grips the rough, dusty surface and gives joint compound a firm base. We then apply the compound with a wide trowel in two or three passes. Each coat fills more of the valleys between the bumps until the old texture no longer controls the surface. The original material remains underneath and undisturbed.

A skim coat over popcorn adds weight and thickness, so it will not correct material that is already loose. Deep texture also takes more passes to flatten than shallow texture. Beyond a certain depth, those extra coats can cost more than scraping the ceiling. We compare the condition of the existing surface with the work needed to remove it rather than treating removal as the automatic choice.

A positive asbestos test result is a separate matter and is not a reason to cover the ceiling. When a positive test comes back, we do not scrape the material or build a new surface over it. We do not work with asbestos. A contractor qualified to handle that material takes over and determines the appropriate method. Once that work is complete and the ceiling is ready for us, we can handle skim coating, sanding and primer.

What Changes Once the Heavy Texture Is Gone

Sprayed acoustic texture stands about an eighth to a quarter of an inch proud of the board, and each small bump casts a shadow beside it. Those shadows take light from lamps and windows instead of reflecting it evenly, which makes the ceiling read lower and darker than a smooth ceiling at the same height. The difference is easiest to see in a room with one window and pale walls. It is less noticeable in a small hallway.

Cleaning changes too. Texture catches dust in its raised surface and cannot be wiped clean in the same way as a smooth ceiling finished with ceiling paint. There is a tradeoff. Popcorn was sold as an acoustic finish and does soften sound in a room slightly, most noticeably in an open plan or beneath a second floor. Removing or covering it gives up that small acoustic effect in exchange for the smoother surface.

What You Get for the Money

The visible return is straightforward: fewer small shadows across the ceiling, more reflected light, and a surface that is easier to clean. The financial return is less certain. Buyers can see a popcorn ceiling as work they will inherit, so removing it beforehand takes that future job off their list. That does not mean anyone can attach a reliable dollar amount to the change.

There is no published figure showing what popcorn ceiling removal adds to a home's value, and we do not price the work as an investment or promise that its cost will come back to you. If resale is your reason for doing the work, the practical choice is to spend the money in the rooms where buyers are most likely to notice the ceiling rather than assuming every finished square foot produces a measurable return.

Testing, Clearing and Sealing the Room Before Popcorn Removal

Before popcorn texture comes off your ceiling, we first settle what the material is, clear or protect everything fixed into the ceiling, and close the room off from the rest of the house. Only then do we introduce water and start scraping. That order matters because testing can stop the removal before anything is disturbed, electrical fittings have to be dealt with before the ceiling gets wet, and open vents or attic penetrations can carry sanding dust beyond the work area.

Testing Pre-1990 Ceiling Texture Before It Is Disturbed

Texture installed before 1990 can contain asbestos, so we arrange lab testing before any scraping begins and remove only material the results clear as safe.

We use 1990 because sprayed stock continued to be installed for years after it stopped being made. Neither the age of the house nor the appearance of the ceiling settles the question. Asbestos testing of pre-1990 ceiling texture starts with small samples from several spots because patches, additions and repairs can leave material from different years on the same plane. One clear sample does not prove that every section is clear.

The lab identifies the mineral under polarized light microscopy rather than judging the texture by appearance, and chrysotile is the type most commonly found. You receive the result in writing, normally within a few days, and nothing overhead is disturbed while the result is pending. If a sample is positive, we do not proceed with scraping that ceiling. A clear result lets the preparation for removal continue.

Fans, Lights and Other Ceiling Openings

Fans and hanging light fittings come down before water reaches the ceiling. Ceiling fan removal takes the blades and motor off to the junction box, the metal box that holds the wiring. Recessed lighting, with cans set into the ceiling so the bulb sits flush, is usually capped or masked in place. We identify anything we are not qualified to disconnect before the workday begins rather than finding it after the room is sealed.

The circuits are switched off at the panel while the ceiling is wet, so the room has no working light for part of the job and we use our own lamps. If a fan or light fitting is already coming down, that is also the least expensive time to replace it. Smoke alarms are removed or bagged so sanding dust does not set them off.

The attic hatch and recessed housings also open toward the attic. We seal them before scraping so loose insulation and dust cannot move through those openings. The same planning applies to air vents and returns cut through the ceiling, especially where the air handler is in the attic and the return grille is one of the largest openings in the room.

Sealing the Room and Closing the HVAC System

Heavy plastic sheeting and rosin paper cover the floor, sheeting is taped up the walls, fixtures and cabinets are masked, and doorways are closed off. We also seal supply openings, returns and HVAC vents. An open vent can pull material from the room into the ductwork and send it elsewhere, which is how dust in the house can start in one bedroom and appear in another part of the building.

The HVAC system is normally switched off while sanding is underway. In Conroe summer heat, that shutdown is worth planning around, and the HVAC filter is worth changing after the work is finished. Dust control continues at the tool itself with a vacuum-assisted pole sander and HEPA filtration because the fine dust comes mainly from sanding rather than from wet scraping. At the end of each workday, the contained room is swept and vacuumed.

Misting, Soaking and Wet Scraping

Once testing is clear, the ceiling openings are protected and the room is sealed, a pump sprayer mists one section at a time. The texture sits for a few minutes so the water can soak through it. A drywall scraper with a broad blade held at a low angle then lifts the softened material from the board in sheets. Working section by section keeps the dwell time consistent.

Too little water leaves the texture powdering under the blade. Too much water can soften and tear the paper facing on the drywall, turning removal into a repair. Water also adds weight, so we check board thickness against framing spacing before wetting your ceiling, particularly where thin board spans widely spaced framing. The goal is enough water to release the texture without leaving any part of the ceiling saturated longer than necessary.

When Paint Stops the Water From Reaching the Texture

Paint over popcorn seals the surface and causes water to shed instead of soak in. A painted ceiling therefore may not respond to the normal misting and soaking sequence. We make a test patch before the job is booked so the problem is found before a room is opened up. If water cannot reach the texture, wet scraping is no longer the same removal job.

Dry scraping removes the texture without water, but it is slower, much dustier and harder on the board underneath. The other option is to leave the texture in place and skim a smooth surface over it. You hear both approaches and the price of each before choosing how to handle a painted popcorn ceiling.

A yellowed popcorn ceiling above a furnished room with a dome light
A trowel worked flat across a ceiling overhead

What the Ceiling Shows and What Goes Back On

Popcorn texture hides the gypsum board, drywall tape, patches and old finish underneath it. The first clear look at your ceiling condition comes after the scrape, so a scope written from the floor has to allow for hidden damage rather than assume the board is ready for paint. Once the surface is open, we check the joints, fasteners, repaired areas and any ceiling water stain before deciding what the ceiling needs next. From there, the work moves in one direction: repair what the texture was hiding, then build the finish you chose over sound, dry board.

What the Bare Board Can Reveal

Some ceilings were finished only far enough to support popcorn because the sprayed texture was always meant to hide the seams. Once it is gone, unfinished joint work, loose drywall tape and nail pops become visible. Loose tape shows as a straight separated seam. Nail pops appear as small round bumps where a fastener has backed out of the framing. A loose seam is re-taped, and a backed-out fastener gets new drywall screws driven into the framing.

Popcorn also hides patches, shallow waves, knife marks and hairline cracks. That matters because a ceiling that looked uniform under heavy texture may not be ready for a smooth finish after scraping. Hairline cracks can return where the house continues to move, and a flat ceiling will not hide them the way popcorn did. We tape joints to resist movement and leave wall angles able to move, then show you any repair area that will affect the finish you choose.

Stains, Moisture and Damaged Board

A ceiling water stain usually points to a problem above the ceiling, such as a roof leak or an attic condensate pan that has overflowed. We pass a moisture meter over the area to check whether the framing above is still wet. Stopping the leak at its source is a separate trade, and we will tell you plainly when your ceiling needs one before we go further. The moisture source has to be stopped and any active mold dealt with before the wall is closed.

Old, dry stains still need attention because they can bleed through fresh joint compound and latex paint. We seal them with a shellac-based stain-blocking primer before the finish goes on. Board that has absorbed enough moisture to turn soft is cut out and replaced. These findings are quoted separately from scraping because the repair depends on what the exposed surface shows, not on the popcorn itself.

Flat Plane: Level 4 and Level 5

If you want a smooth ceiling, scraping is followed by skim coating. We spread joint compound across the whole ceiling with a wide trowel instead of treating only the seams. Two or three skim passes build the surface, with sanding between coats and full drying before the next pass. A closed-up house during a Gulf Coast summer can stretch drying time, so we may use setting-type compound or a dehumidifier to keep damp compound from shrinking later and leaving visible lines.

Level 4 and Level 5 describe the smooth finish standard. A Level 5 finish puts a skim coat across the full surface and gives the most control over what critical light reveals. Light from large windows, recessed fixtures and open plans travels across the ceiling and exposes waves that a central bedroom fixture may not show. You can see the same effect by looking along the ceiling toward the far wall instead of straight up at it.

Light Texture: Retexture After Popcorn Removal

A light texture takes fewer passes than a full skim and can make more sense on a ceiling that has been opened and patched several times. Where board was cut for a leak, wiring or another repair, a retexture after popcorn removal can disguise small plane changes that a smooth finish would put on display. It also gives old hairline cracks less visual emphasis than a flat plane, though any loose joints or damaged board still have to be repaired first.

Knockdown, orange peel and skip trowel are the usual options. Matching the pattern to ceilings you are leaving untouched can keep a part-house job consistent without forcing every room into a Level 5 finish. Whichever finish you choose, we complete the repairs, apply the selected surface, prime the ceiling and hand it back paint-ready.

Why Choose Conroe Drywall Co. for Popcorn Ceiling Removal

When a homeowner anywhere in our service area wants an insured drywall contractor to remove popcorn ceiling texture, this is the process Conroe Drywall Co. puts behind the quote before any work is booked.

  • Conroe Drywall Co. has been removing popcorn ceilings throughout Conroe and Montgomery County for over 15 years.
  • We are insured and follow established industry practices, including ASTM C840 standards for gypsum board installation and finishing.
  • Your scope is provided in writing, with the finish you choose listed at its own price, so you know exactly what you are agreeing to before the work begins.
  • Lab testing is arranged whenever the age of the ceiling requires it, and nothing overhead is disturbed until the result comes back.
  • Work areas stay under containment, keeping the job inside the room being worked on while the rest of the house remains available to you.
  • Any allowance for damage uncovered during scraping is listed separately, so there is already a price attached to hidden repairs before anything is found.
  • Our on-site estimates are free, and financing is available for larger projects.

To schedule your free on-site estimate, call us at (346) 488-0243.

What Popcorn Ceiling Removal Costs in Conroe

We price this work by ceiling area, the square footage of ceiling being scraped, then adjust that price for the condition of the surface underneath. We do not publish a popcorn ceiling removal cost per square foot on this site because the board above the texture cannot be graded until the texture comes off. A ceiling that scrapes clean and one hiding loose tape or soft board may be the same size, but they are not the same job. The written estimate you receive after the on-site look sets your price, and you can check most of the factors that affect it from your own floor.

What Moves the Price on a Ceiling Scrape

These cost factors determine the labor hours and equipment required for a ceiling scrape:

  • the ceiling area, which sets the base price before any other factor is added
  • whether the texture has been painted, which can double the labor required
  • ceiling height, since an 8-foot standard ceiling is reached from a pole while a 12 to 18-foot vaulted ceiling requires scaffold, the staged platform we build to stand on
  • whether the room is furnished or empty, because the floor and anything left in the room are covered before work begins
  • how the room is lit, because grazing light, which rakes across the ceiling from a nearby window or fixture, reveals every ridge and raises the finish level we need to reach
  • how much repair the scrape uncovers beneath the texture
  • whether you want a light texture or a fully flat plane

Removing It or Covering It: the Honest Comparison

Neither route is automatically cheaper, and each puts more of the cost in a different place. Scraping uses more labor and less material because the hours go into wetting the texture, removing it, and then flattening the surface that was hidden underneath. Covering uses more material and less labor because the flat plane is built up with compound over the existing gypsum board instead of uncovered. Over sound board with unpainted texture, removal is usually the better buy.

Call us at (346) 488-0243 and we will inspect your ceiling and give you a written price.

A popcorn ceiling over an older living room with a brick fireplace and ceiling fan A worker standing on a box to run compound along the top of a wall

What Removal Day Looks Like in Your Home

At Conroe Drywall Co., the job moves from the first look at your ceiling to a primed surface ready for a painter, and the popcorn ceiling removal process follows six steps over a small number of visits. You are there for two of them: the initial inspection and the final walk-through. In between, our crew works in the room you have handed over. How long does it take is better answered in calendar days than labor hours, because coats dry between visits.

  1. 1

    The First Call, the Test and the Written Scope

    You tell us what is overhead and send us a photograph.

    The first contact takes only a few minutes. Tell us roughly when the house was built and which rooms you want done, because the age of the house determines what has to happen before we touch the ceiling. A photograph is more useful than a description, especially one taken from the side with the camera aimed along the ceiling rather than straight up at it, since that angle shows the texture depth and how it was applied. The photograph narrows down what we are looking at; it does not set the price.

  2. 2

    We come out, identify the texture, and provide a written scope.

    We come to your home, identify the texture by sight, and take a small sample when the age of the house requires one, both on the same visit. Your scope then comes back in writing with two items listed separately: the finish you chose for the bare ceiling and an allowance for whatever the scrape uncovers. That second line gives any hidden repair a price you agreed to in advance instead of producing a new number halfway through the job.

  3. 3

    Sheeting Up and Scrape Day

    The room is cleared and fully sheeted for protection.

    Before we start, you clear out the small items: ornaments, electronics, anything breakable, and anything you would rather not have someone else move. We handle the heavy furniture, then sheet and seal the room before anything gets wet. Once the sheeting goes up, the room stays out of use until the primer is on.

  4. 4

    The texture is removed.

    A single room usually takes one day from the first pass to a swept floor. The texture comes off wet, keeping it heavy enough to fall rather than drift, and we bag it as it comes down instead of letting it sit. As each section of ceiling is exposed, we inspect the board underneath and note anything that needs repair before the finish coats go on.

  5. 5

    Coats, Primer and the Walk-Through

    Joint compound, sanding and ceiling primer follow.

    The finishing visits are what stretch the calendar, and a humid week in Conroe adds more drying time. We sand the ceiling between coats, capturing the dust at the tool as it is created, and apply ceiling primer last to leave an even surface ready for paint. If a coat needs another day to dry, we give it that time rather than covering compound that is still soft.

  6. 6

    We walk the finished ceiling with you, then remove the sheeting.

    At the end, we walk the ceiling with you under the room's own lighting rather than a work lamp, because that is the light you will see it in every day. We then remove the sheeting, clean the room down, and hand it back with the ceiling primed and ready for paint. To book the on-site visit, call (346) 488-0243 or send us the details through the quote form.

The Jobs That Sit on Either Side of a Ceiling Scrape

Not every ceiling call is a scraping job. Some work needs to happen before the texture comes off, while other work begins after the ceiling is flat again. Each is a separate service with its own price, so it helps to ask for the one you actually need by name.

Before: a Ceiling That Is Already Damaged

A ceiling that is cracked, sagging or stained but keeping its existing texture falls under ceiling repair rather than removal. Board that has been soaked by a leak is a water damage rebuild because wet gypsum board loses strength and needs to be replaced instead of patched. A plaster ceiling in an older house requires plaster repair, since it is a different material and is worked differently. If damage is the reason you are calling, we address that first. Scraping over a ceiling that is still failing underneath only lets the problem come back through the new finish and leaves you paying for the same area twice.

After: Texture, Primer and Paint

Matching an existing texture or applying a new one as a standalone job falls under finishing and texturing. The finish coat of ceiling paint over a surface we have already primed is part of priming and painting, while hanging a completely new ceiling falls under ceiling installation. Our scraping work ends with the ceiling plane primed and ready for paint, so finish painting has its own price and adds to the number of visits.

A popcorn ceiling half removed with the pole scraper still against it

Popcorn Ceiling Removal in Conroe and Across Montgomery County

Sprayed texture was the standard ceiling finish for decades, so the first thing we ask about your house is its age rather than its street. Conroe has a humid subtropical climate and receives about 51 inches of rain a year, and that damp air slows drying between coats, so we plan the finishing visits around those conditions.

Where Conroe Drywall Co. Takes Popcorn Ceilings Off

Conroe Drywall Co. removes popcorn ceilings across a service area of 21 communities, grouped here by location. The service area reaches just past the county line to New Waverly in Walker County and Plantersville in Grimes County.

Conroe Neighborhoods and Communities

  • Grand Central Park
  • Graystone Hills
  • Rivershire
  • Stewarts Forest
  • Downtown Conroe
  • Wedgewood
  • West Fork
  • Tejas Creek

Surrounding Cities and Communities

  • Willis
  • Montgomery
  • New Caney
  • Splendora
  • New Waverly
  • Cut and Shoot
  • Panorama Village
  • Grangerland
  • Plantersville

Lake Conroe Communities

  • Lake Conroe
  • Bentwater
  • Walden on Lake Conroe
  • April Sound

Popcorn Ceiling Removal Questions

How much does it cost to remove popcorn ceiling?

Two things set the price: how much ceiling there is and what condition the board is in once the texture comes off. You will not find a published rate for popcorn removal anywhere on this site because a square-footage figure alone does not tell the whole story. A phone quote based only on ceiling area will change if the texture has been painted, the board underneath is damaged, or the surface needs more filling before it is ready for paint. Your written price comes after we inspect the ceiling in person.

Do I need a permit to remove popcorn ceilings?

Taking one ceiling finish off and putting another back is finish work: no framing is cut, moved or added, and no wiring or ductwork is altered. That is generally not the type of work a building permit is written around. The answer changes if the job expands into new framing or a new ceiling, which falls under a different scope. Because permit rules are set locally, the City of Conroe building office is the authority that can confirm what applies to your address, and that confirmation is free.

How long does it take a professional to remove a popcorn ceiling?

Count the job in visits rather than hours because drying time sets the calendar. Scraping one room usually takes a day, but each coat of compound that follows has to harden before the next one goes on, so a single room commonly takes two or three visits and a whole single-story house stretches across several days. The elapsed time is longer than the hands-on work, and adding more people does not shorten it. What does shorten the schedule is the compound we use and a dehumidifier in the room, not a larger crew.

Is it better to cover popcorn ceilings or remove them?

Remove the texture when it is unpainted and the board above is sound, because it comes off wet and leaves a surface we can finish directly. Covering is the better choice when the texture has been painted or when years of patching have already left the ceiling thick and uneven. Because covering adds both thickness and weight overhead, we check the framing before you choose that route.

Will removing popcorn ceiling increase home value?

Nobody can tell you exactly what the work will return, and we will not put a figure on it. What we can say is that most buyers see a textured ceiling as a future expense, while a smooth ceiling removes that concern from the conversation.

Is popcorn ceiling removal messy?

Yes. Soaked texture comes down in wet sheets, while the sanding that follows creates fine dust, so the entire process is built around keeping both contained inside the room we are working in. The stage people expect to be the messiest is actually the scraping, but the wet scrapings simply drop onto the sheeting and are bagged in the same room. The fine dust comes later, when the dried compound is sanded smooth.

Can you take the popcorn off just one room?

Yes, one room on its own is a normal job for us, and plenty of our work is exactly that. The boundary is worth thinking about before we start. Put it at a wall rather than an opening. An open doorway, arch or ceiling that continues into a hallway places the transition where people look straight at it, while a wall gives the change in finish a natural place to stop.

What happens if the test comes back positive?

The texture stays exactly where it is, and the job passes out of our hands. Someone qualified for that material takes over, and once the ceiling is ready to come back to us, we finish it. The written test result belongs to you, so keep it and give it to whoever handles that work rather than paying for the same test twice.

Get a Price for Your Ceiling from Conroe Drywall Co. in Conroe, TX

The next step is simply a look at the ceiling, not a commitment. We work throughout Conroe, Montgomery County and the surrounding communities, and a free estimate gives you a written price before you book anything. Read the quote, take your time with it, and decide when you are ready.

Call (346) 488-0243 or use our quote form for a clear price on your project.